1

Topic: disk read error occurred after update of insertion BIOS

Hello!
Configuration:
The motherboard: asus p5n-e sli
The processor: Genuine Intel (R) CPU 2160 1.80 GHz, 2 CPU (s)
Storage RAM: 2046
BIOS: Phoenix - AwardBIOS v6.00PG
The videocard: NVIDIA GeForce GT 240 1
System: Windows XP Professional (5.1, the assembly 2600)
Updated BIOS from version 0505 (2007/03/16) to version 1406 (2009/11/30) then on the start screen the following error started to be written:
"CMOS checksum error - Defaults loaded".
Dropped adjustments BIOS on default. Then no error with CMOS is present, but now after flashing of all start screens other error is written:
"disk read error occurred
press ctrl+alt+del to restart"
In what the reason can be, and how it to cure?
Already  some variants, but all it like not about that: the computer did not fall, accordingly winchesters were not damaged, in a computer interior did not climb, any "incorrect setting of operating systems" were not, is equal as generally any setting, anything at all did not touch, except as soon as  updated also its adjustments on default exposed.
Hard disks (3 ) in  are defined all. The system is installed on from what I try to boot, is selected by the first in sequence.
In advance thanks.
___________________________________
I update the information.
The flash card is disconnected.
Screws are available the following:
SATA 1: Samsung SP2504C 250
SATA 2: Samsung SP2504C 250
SATA 3: Hitachi HDT725050VLA360 500
The Windows from Hitachi, but the main system on Samsungah boot only. At a choice of loading with Sata 1 or with Sata 2 - an error "disk read error occurred".
By the way, Keys F8-12 at all do not work at loading, do nothing. It is possible to come only in Bios by means of Del.
And still now at the first switching-on of a computer there is any error on the start screen:
"Warning! CPU has been changed.
Please re-enter CPU settings in the CMOS setup and remember to save before quit."
Further it is possible to push F1 and to pass, indifferently, at reboots of an error is not present.
Tried then to disconnect all screws from cables and to connect on one. At connection of the screw which has been connected on Sata 1 - an error:
"Disk boot failure, insert system disk and press enter"
It turns out, screws died?
Connected all screws reversely, booted on working (the truth, semibroken) Hitachi Windows (XP) - in "My computer"  screws are defined, but do not open in any way:
"There is no access to I:\
The file or folder are damaged. Reading is impossible.
The disk in device J is not formatted.
To produce its formatting?
The disk in device K is not formatted.
To produce its formatting?"
Disks died also to program recovery are not subject?
It is interesting, as they could die from update and reset of adjustments of Biosa...

2

Re: disk read error occurred after update of insertion BIOS

Serp2015
It is interesting, as they could die from update and reset of adjustments of Biosa...
And they, casually, not in spot-check were?

3

Re: disk read error occurred after update of insertion BIOS

Thanks for answers!
VovGan
"CMOS checksum error - Defaults loaded".
It on idea should not be was, but sometimes happens. In this case most likely a problem that in the intermediate versions something changed so that adjustments naturally went wood, basically. In that case it is recommended to make after an insertion clear cmos

And I will make... I Want to try at first only with screws to understand.
The Variant two - you simply stitch yours 0505 backwards. All.
And tried to make.
Downloaded version 0505 (which was initially), loaded in a flash card root, came into utility EZFlash 2 in most  and selected a file with the 0505-version, after perusal writes the message: "Downgraded ROM file was not suitable for the system."
Prompt, please, and how then  to make?
GrayWolf
And they, casually, not in spot-check were?
Raid i.e.? And how to learn?) computer  from acquaintances, a little bit only .

4

Re: disk read error occurred after update of insertion BIOS

Serp2015
How then  to make?
From under DOS. http://www.pontin.ru/technical/firmware … -bios-asus

5

Re: disk read error occurred after update of insertion BIOS

Serp2015
Raid i.e.? And how to learn?)
I do not know. And it is necessary? If there is not present important  to connect to a working computer and .
Simply two identical hards and messages  as at scattered spot-check - suggests.

6

Re: disk read error occurred after update of insertion BIOS

Most likely both Samsunga were in Raid, and at  values of adjustments BIOS Raid is disconnected.
It is necessary to include in adjustments BIOS RAID a mode after that to expose loading from array RAID and should earn all.

7

Re: disk read error occurred after update of insertion BIOS

Thanks for answers!
a1039
From under DOS. http://www.pontin.ru/technical/firmware … -bios-asus
Alas, all this bedlam does not work for me. Tried and so, and : both with AFUDOS, and with BUPDATER (downloaded from an official site of Asus an insertion of Bios of version 0505 (0505.BIN)), no variants of commands worked: wrote or "ASF Signature not found", or the dark blue screen and the orange message: "Failed to find the update module" (for example, after a command bupdater/i0505.bin/pbnc).
But it turned out to roll away an insertion from Windows of the working screw of Hitachi by means of aaplet Award Winflash 1.94, downloaded from here: https://www.wimsbios.com/awardflasher.jsp In article pontin.ru like it also is mentioned but where to download - I long searched...
Directly from Windows the aaplet delivered the 0505-version. However, that is strange, now at computer switching-on though is written that  0505, but there was a start color picture from new  (1406) which earlier on 0505th version was not...
GrayWolf , denis110674 , VovGan - many thanks for idea!
Rollback  solved nothing, but the problem appeared  in the flied adjustments of it RAID. Came in  in Advanced-> Onboard Device Configuration-> NVRAID Configuration-> RAID and made it enable, and also enable for SATA 1 and SATA 2, and all booted... ))))
Once again many thanks for the decision. Long, truth, searched, where this  to include...
And I made a load flash card for XP with everyones recovering given by aaplets though that all the same did not work: after a choice of loading from a flash card simply white dash blinks endlessly... Glory to dances with a tambourine, these aaplets any more are not necessary.
And still such question. All these three pieces of the screw dirtied and old, and it is not enough place, and Windows XP somehow not so already.
Whether it is possible to deliver on this iron the screw with SATA III on 3 TB and to deliver there Windows 10, well or at least Windows 7? Screw model: Toshiba 3TB 7200rpm 64MB DT01ACA300 3.5 SATA III
Iron: asus p5n-e sli (at , judging by characteristics, SATA II); Genuine Intel (R) CPU 2160 1.80 GHz, 2 CPU (s); RAM 2046; NVIDIA GeForce GT 240 1 .

8

Re: disk read error occurred after update of insertion BIOS

Serp2015
Whether It is possible to deliver on this iron...
Storage though to 4 to lift.
And a stub on C2D 6xxx to replace (now they there are copecks)