1

Topic: Temperature for WDC WD20EADS

Recently bought the screw from WD. Second-hand but like the serviceable. But something is strongly heated. Programs Ashampoo HDDControl and Crystal DiskInfo show temperature 47-49 hailstones of Celsius. Delivered on it the heat sink: almost any result. In total the temperature fell to 2 degrees, with 49 to 47. What should be its working temperature? Something did not find.
-------------------------------------------------------------
And you enclosed already the blood rouble in Bill Gates's 50 milliard state?

2

Re: Temperature for WDC WD20EADS

More densely  on the Internet. Almost all write that WD Green should be cold - 29 in idle time, 31-32 under loading at 26 exterior temperature. But some complaints that WD is terribly heated got. To 47 degrees But a solution of a problem it is not resulted. It is not found. Who can faced such problems?

3

Re: Temperature for WDC WD20EADS

12/4/2017 10:56, Joss writes:
> Recently bought the screw from WD. Second-hand but like the serviceable. But something is strong
> It is heated. Programs Ashampoo HDDControl and Crystal DiskInfo show
> Temperature 47-49 hailstones of Celsius
And actually it really such high? Generally speaking, it
Green, i.e. , and they are heated a little.

4

Re: Temperature for WDC WD20EADS

12/4/2017 11:56, Joss writes:
> Almost all write that WD Green should be cold
It follows from it . And if it at you is really strongly heated -
It becomes clear, what for to you it sold wink.

5

Re: Temperature for WDC WD20EADS

Dim2000 wrote:

And actually it really such high? Generally speaking, it
Green, i.e. , and they are heated a little.

Yes it is really strongly heated. Touched a hand. Very hot. Attached to it the heat sink, but result weak. What to do - I do not know. Any more you will not return.

6

Re: Temperature for WDC WD20EADS

Put a valve on it blowing.
At me was 3 , 2 of them just as at you on 2, the temperature not above 30 with small was, they cold, are more exact warmish)
With yours explicitly any jamb.

7

Re: Temperature for WDC WD20EADS

"Very hot" - too subjective appraisal. Measure more precisely and try to define a heating source (a controlling board, the unit of heads, the engine).
(Any) the forced cooling is rather recommended to spindles, will be the normal case fan in half-speed enough. Otherwise there are absolutely different indexes on heating depending on layout of disks in the case and a construction of this case.

8

Re: Temperature for WDC WD20EADS

12/4/2017 13:29, Joss writes:
> Yes it is really strongly heated. Touched a hand. Very hot. Attached to
> To it the heat sink, but result weak. What to do - I do not know.
It is abnormal. Put blowing.

9

Re: Temperature for WDC WD20EADS

Scott Tiger wrote:

"very hot" - too subjective appraisal. Measure more precisely and try to define a heating source (a controlling board, the unit of heads, the engine).

Programs show 47-49 degrees. Touched the case, there where connectors. Could not define. Probably it is necessary to ungear a computer. To allow to cool down to the screw. Then to turn on and try to define a source did not heat up yet. When heated up - it is impossible to define.

10

Re: Temperature for WDC WD20EADS

Dim2000 wrote:

It is abnormal. Put blowing.

Itself I understand that is abnormal. Before was WD6400AACS - was warmish, but it started to be strewed. Decided this to take on changeover. And here such focuses...

11

Re: Temperature for WDC WD20EADS

Tested Victoria. It can is possible to change any parameters of a disk that it was heated less?

12

Re: Temperature for WDC WD20EADS

Joss;
Hammer, dies - you will buy another